Techleader is professional 自動スクリューフィーダーマシン,自動スクリューロック機,ロボットネジ固定システムと 自動ねじ締め機 中国のメーカー.
今日は、適切な自動スクリューフィーダーマシンの価格で適切な材料を選択することについて話します.
自動スクリュー駆動機
Not only choose the right material for the material, but also the food control systems. An example is the automatic funnel filling control. If the container is filled too frequently, the controller will need less time to measure the weight loss, which can affect the accuracy of the loader. On the other hand, if the filling level in the hopper falls too low, the sudden pressure of the material falling into the hopper during filling may cause the material to flow through the screw, especially for low density pulps. and slightly fluidifying materials. Since this material flow falls into the 自動スクリューフィーダーマシン price, this leads to a temporary increase in the load of the motor, which leads to an increase in the torque in the control screen of the extruder. These torque peaks must not exceed 100% of the available torque of the extruder. Otherwise, the safety latches will stop the extruder to avoid overloading. As a result, the normal operating torque of the process must be kept lower to make room for these possible peaks.
The increase in efficiency with the optimization of the automatic screw feeding system can be calculated by the increase in productivity. Table 1 shows an example of its calculation for a 70 mm twin screw extruder, which processes a automatic screw feeder price with a profit margin of 10 [/ カテゴリー]. In this example, a feed that experienced an increase in filling was replaced with another one more suitable for the material, which increases the flow from 2,000 カテゴリー / h to 2,300 カテゴリー / h (4409 に 5,070 lb). / h). The result is an additional annual benefit of $ 180,000, more than four times the cost of the new sender. In addition, as the degree of filling of the twin screw extruder increases, the specific mechanical energy supply for the material increases. This means an energy saving of 5% or 138 自動スクリューフィーダーマシン price / 年.
FOOD RECEPTION
After the feed system has fed the material to the 自動スクリューフィーダーマシン price, it must be directed downstream to the feed area. The flow is limited if the entrance area does not have sufficient capacity to transport materials. The transport capacity of the feeding area is determined by the free area of ??the twin screw and the inclination of the screw elements in that area, as well as the speed of the screw and some specific parameters of the product.
The free cross section of the 自動スクリューフィーダーマシン price is fixed in a standard twin screw extruder. Extruders with a greater external diameter / inner diameter ratio have a larger free area. This must be taken into account when buying a new extruder. The parameters of the product are related to the selection of raw materials. Changes are often complicated for reasons of purchase or product quality.
The parameters that can be optimized in an existing machine are, したがって, the pitch of the screw elements and the speed of the screw. An increase in screw speed usually leads to a greater input of energy into the material. This increase in energy can be partially compensated by increasing the feed rate. 今日、ほとんどすべてのデジタルビジネスで非常に一般的になっています, this increase tends to be trained by increasing the speed of the screws. This leads to a higher melting temperature which, among other disadvantages, can lead to problems with granulation or product quality.
In conventional polymerization processes, there is a melting zone comprising a section of mixing blocks that are completely filled with polymer. Since this section of the automatic screw feeder price is completely filled, entrained air can not pass through the molten polymer downstream of the molten seal. In conventional polymerization processes, there is a melting zone comprising a section of mixing blocks that are completely filled with polymer. Since this section of the extruder is completely filled, entrained air can not pass through the molten polymer downstream of the molten seal. Instead, it must escape through the nearest upstream opening, which is normally the feed opening . As a result, there is a competitive flow of raw materials and effluent air.
For more about 自動固定ねじ機の選び方,you can pay a visit at https://www.automatedfl.com/product-category/automatic-screw-locking-machine/
About Techleader
Techleader
Techleaderは恵州Shengyang工業株式会社のブランドです。, 株式会社.
恵州盛陽工業株式会社, 株式会社. Rに特化しています&Dおよび製造電子機器産業製造自動化機器。 自動スクリューフィーダーマシン,自動スクリューロック機,Dおよび製造電子機器産業製造自動化機器。,自動ねじ締め機 タービンエアブロー自動フィーダー, 三次元測定機, 自動ディスペンサー, ペリスタルティックディスペンサー, 自動接着剤充填機, 自動はんだ付け機,生産自動化ラインと電子自動化アセンブリを主導しました。私たちは、グローバルな顧客向けに自社ブランドのTechleaderを使用して製品を運用し、多くのOEMも行っています。&お客様のためのODM生産.
For product inquiry,please contact:
M1-M4ネジロックは、送りネジモジュールを交換することで実現できます: M1-M4ネジロックは、送りネジモジュールを交換することで実現できます
M1-M4ネジロックは、送りネジモジュールを交換することで実現できます: 恵州盛陽工業株式会社, 株式会社
M1-M4ネジロックは、送りネジモジュールを交換することで実現できます: Dビル,金泰陽工業団地,Xingye Road,仲愷地区,恵州,広東,中国
M1-M4ネジロックは、送りネジモジュールを交換することで実現できます: 86-752-6682869
モバイル:+86-13352636504
Eメール: [email protected]
M1-M4ネジロックは、送りネジモジュールを交換することで実現できます:https://www.automatedfl.com
